DIY Halloween Decorations: No-Sew Ghost Chair Covers

Decorating for Halloween (or any holiday) can be a costly endeavor. This year, I decided to create my own Halloween decorations. My goal was to create easy one-of-a-kind decorations that can easily be repurposed for other holidays – with a few minor tweaks.

I began my Halloween crafting by creating a Halloween wreath that can be reused for Thanksgiving, Christmas – and probably even Spring or Summer – simply by changing a ribbon and a few decorations.

Once I had the front door looking festive, I moved inside and created jack-o-lantern and ghost chair covers. This no-sew fabric craft is the perfect addition to any Halloween house. In addition, because I used Velcro to attach the ghost features, when Halloween is over, the ghost faces can be removed and replaced with Thanksgiving, or even Christmas imagery.

oyveyaday.com

Click here for printable instructions for the No-Sew Ghost Chair Covers.

Click here for a printable ghost face template.

Supplies

  • White Felt (amount will depend on the size and number of the chairs you want to cover)
  • Black Felt
  • Measuring Tape
  • Straight Pins
  • Scissors and/or a rotary cutter
  • Cutting Mat (if using a rotary cutter)
  • Straight Edge (I used a large t-square)
  • Heavy duty iron-on adhesive (such as Stitch-Witchery or Heat Bond)
  • Velcro
  • Iron
  • Pressing cloth (I used a tea towel)

Instructions

Measure and cut fabric

  1. Determine how long you want the back of your chair cover to be. (I like the back of the cover to end just below the seat brace.)
  2. Length: Run the measuring tape from the seat of the chair, over the top and down the back to the spot where you want the chair cover to end. This measurement determines how long your fabric needs to be.
  3. Width: Measure the width of your chair back at the widest point. Add 2 inches (1 inch per side) to leave room for the iron-on adhesive, and ensure that the cover isn’t too tight.
  4. Cut your fabric using the length and width measurements from steps 2 and 3.
    oyveyaday.com

Iron seams using iron-on adhesive

  1. Place the fabric over the chair, with the front resting just on the seat of the chair, and then pin the sides of the fabric.
  2. Pull the pinned fabric off of the chair and head to the ironing board.
  3. Follow the instructions on your iron-on adhesive package to create your no-sew seams (using a damp pressing cloth makes it much easier).
    oyveyaday.com
  4. When the seams are done, turn the fabric right-side out. Be sure to push out both top corners.
  5. Because the back is longer, you will notice that the bottom of the chair cover is now wider than the rest of it. You have several choices on how to deal with this: 1) Leave it as is; 2) Cut away the extra fabric (making sure that both sides are symmetrical and straight); or 3) Fold the wider edge in, lining it up with the seam, and then use iron-on adhesive to secure it. I chose option 3.
    oyveyaday.com

Add the ghost face

  1. Cut out ghost features from your black felt. You can do this freehand or use my template.
  2. Cut out small pieces of the hook (hard) side of a strip of Velcro, and attach them to the corners/edges of your ghost features using the same iron-on adhesive you used to create the chair cover.
    oyveyaday.com
  3. Stick the ghost features directly onto your chair cover. It is a good idea to do this when the cover is already on the chair so that you get the features exactly where you want them.

Do you have a favorite Halloween decoration? Is it homemade or store bought?


Comments

    • says

      I can’t decide which I like better, either. I know my boys love the jack-o-lanterns (or punkins, as Max calls them), but I think I might be partial to the funny-faced ghosts.

      Glad you like them both!

Trackbacks

Leave a Reply

Your email address will not be published. Required fields are marked *

CommentLuv badge